draindanger87

Peugeot 208 Key Replacement It is better to leave the replacement of Peugeot keys for 208 to auto locksmiths that have the required equipment and expertise. They will be able to create and program new keys much quicker than a dealership and at a lesser cost. If your key fob stopped locking or unlocking your doors it could be due to a dead coin battery. There are also other reasons that the key might be malfunctioning. Dead Coin Battery A dead battery can stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. If this is the situation, you'll need make use of the backup starting procedure which is explained in the owner's manual for your vehicle. Another reason why the 208 won't start is that the spark plugs have been worn down. The spark plugs are responsible to ignite the fuel that starts the engine. However they have a short lifespan. If they aren't used enough to last, they'll eventually fail. There is an easy solution to this issue. Verify the voltage of your battery with a multimeter. If it's less than 11.5 volts it is time to replace it. It is also essential to clean the contacts of the battery in the event that it is damaged by corrosion. You can do this by lifting the rubber covers that protect both battery terminals and using a wire brush to remove any corroded components of the battery. Then, reconnect the cables that connect the positive and negative poles. Water Damage If your 208 will not start and the battery has not fallen flat, it is time to inspect the spark plugs. You might find that they're dirty and do not spark. The spark plugs can be cleaned in an workshop. Peugeot cars are equipped with a transponder key that is compatible with the car's immobiliser system. This makes sure that only the correct key is able to start the engine. If the chip in the Peugeot key is damaged then it won't send the correct signal to the vehicle. Water damage is a frequent cause of this issue. This is particularly common in colder climates where the vehicle might have been exposed to rain or snow. In this instance, you should contact an experienced locksmith who will have the tools and equipment needed to modify the key. They will also have the latest technology and equipment required to make a Peugeot smart key. The process should not take more than 15 minutes. Contacts of the battery may be damaged. Peugeot changed from the old carbon-encased transponder chips to an entirely new type of chip that incorporates electronic components within circuit boards. More suggestions is effective when it's brand new but as time passes, the circuit boards start to deteriorate and stop working correctly. This could prevent the immobiliser chip from activating and causing your car to not start. Contact a Peugeot specialist or a locksmith if this is the situation. The most frequent issue is when the battery in the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery, and then cut a fresh blade for you. This is a simple solution. Faulty Receiver Module It could be that the receiver module is faulty when your Peugeot key fob fails to function after being dropped on the floor, exposed to a stormy rainstorm, or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer which regulates the central locking system of your Peugeot vehicle. The key fob itself has rubber seals that block water from getting to the electronic chip inside. However, prolonged exposure to water could cause damage to these seals and the chip. The high salt content of the ocean or pool can cause damage to the key fob, especially if it is submerged. The module will need to be replaced if your Peugeot spare key does not work anymore. This can only by done by an Peugeot specialist or a professional auto locksmith. Unlike other cars, Peugeot keys are protected by an unique immobilizer system that requires the correct coding to start the engine. This is the reason that you should only rely on the Peugeot locksmith to design and program an alternative. Computer with a problem on board The on-board computer in your Peugeot is responsible for a variety of systems in your car, including airbags and power windows. If something is wrong with these systems, it will typically show a code that identifies the issue. This code is stored inside the system and will remain there until the issue is solved. This will often require the on-board computers to be replaced. The most typical reason for the warning light of the airbag to flash is corrosion or loose connections in the sensor. This can occur due to wear and tear, ageing, or exposure to moisture and salt. This problem should be addressed as soon you can, since an airbag that is malfunctioning could pose danger in the event of an accident. If your Peugeot is showing a card that is not being detected error, then the battery in the key fob might be dead or weak. This will stop the key fob sending a signal to deactivate the immobilizer in your vehicle. Try this by pressing the unlock button on the fob's key, then trying to start your car. If this does not work the battery on the key has to be replaced.